Видео

Hello, thank you for your interest. The target is made from a foam, we designed ourselves, called DynaFOAM. It is a 12 pound density, compressed and bonded from different materials. This target is not designed to be repaired, however it will give you many hours of shooting pleasure.

Hello, We make the foam in our factory, we have several options available, www.archerytargets.com/elastafoam

We have changed the foam, made in house now, called DynaFOAM. www.archerytargets.com/range-beast-complete-kit-boyb48-using-all-new-mdl-dynafoam

Hi Derek, Thank you for your interest in our products. Our website is www.archerytargets.com or you can call the factory direct at 812 937 7185 Thank you!!

Hello, we have changed to a new foam, which is better, and it comes with the compressor. www.archerytargets.com/range-beast-complete-kit-boyb48-using-all-new-mdl-dynafoam

It is bonded, closed cell foam, it is unaffected by the elements.

@@archerace7 aight bet

@@frightenedfatplebbyboie2309 BET

BET!

It works well with my 70 lb set up, with 500 grain arrows, that is the heaviest I have shot it with.

Strange he didn't answer your question .

@@Sertao2013 LOL

You're an adult right? IT'S CALLED MUTE!!!!!!

Our new beast line of targets, should work fine!

@@archerace7 thank you

The foam will take alot of shootng, the inner material does all of the stopping, while the foam holds the arrows straight. The CompCube series has a three year warranty against pass throughs, even after the foam is worn, it will still stop arrows,

Thank you very much! Glad you liked the Beast!!

Sorry for the delay in answering, my Computer went down, I would not recommend this for Crossbows, once you get over 350 FPS the bolts are really hard to remove.

@@archerace7 thanks

We make it in house.

@@archerace7 i doubt that, being in that industry for forty years

@@electoplater you are welcome to come to the factory when ever you want

​@archerace7 you decimated his life long career with 12 words. Well done sir😂

We no longer offer this target system, we have replaced it with a less expensive, but better range target system, with a layered material. Here is a link to the target, for pricing to Bolivia, please email our sales dept Sales@archerytargets.com www.archerytargets.com/range-beast-complete-kit-boyb48-using-all-new-mdl-dynafoam

Thank you for your interest, here is a link to the page. Thanks again!! www.archerytargets.com/the-deadstop-500

archerace7 thank you for your reply back. Much appreciated

Cameron Stewart yeah, that IS an important ingredient ya need for shooting these targets

The Beast targets are rated from 325 to 450 depending upon the model.

Not very well, A bolt at that speed would be storing 450 Foot Pounds of Kinetic Energy....Any foam target that would stop it, would never let you have the bolt back...lol.

@@archerace7 well i have seen others make this similar target with old carpet. You think that might be able to stop it? Since it wont be foam to melt

@@blakebrowder5184 The carpeting is really hard on arrows, and very hard to remove arrows from. We have recently began using a new foam called DynaFoam, which works really well, it is a higher density, and stiffer, will not melt to the arrow shaft. Can still be tight with high power crossbow to pull bolts, but with some arrow lube it is not bad. Call Mike at 888 233 1976 THanks!

We have not gotten production up yet, they will be available on our website June 1st, and at dealers nation wide. www.archerytargets.com Thank you very much for your interest.

Just checked it, it is up.

www.archerytargets.com

Hi Scott, The Bowhunter RPM Extreme is 34"x34" by 20" thick. The new RPM has been upgraded to use an additional bag built into the back of it, for extreme target practice. We can easily change the deer to a hog for you, we do have a catalog, I will be happy to email one to you. The Range Beast Kit is now available. Feel free to call the factory toll free at 888 233 1976. Ask for Mile Wulf, give him your email address and I will send a digital version of our catalogs. Thank you!

All of the materials come with it. To figure the cost of a target, you must figure the cost per shot. There is no target available that will have a lower cost per shot than elastifoam, which if you want to build your own compressor is 379, not to mention we run specials on it often, call 888 233 1976 for specials. We also have now introduced the Range Beast with Dynafoam. at 370 delivered this kit cannot be beat.

Not this target, but we have an inexpensive broadhead target that works fine up to 400 FPS, and probably a good bit more, with good arrow removal, you have to unscrew the broadhead from the arrow before pulling the arrow out. The Black Hornet Aggression. www.archerytargets.com/black-hornet-aggression-broadhead-target

@@archerace7 just received mine in the mail today and will test it later. but mine didn't come with a handle. also there is a space between the mesh and the inner bit of the target, it did not look like that on the video but maybe thats just a trick of the camera. may i ask what that space is for?

@@carls.6746 I apologize for the lack of handles, They should have been on it, I will send you something to make up for it. The space is to keep the arrows straight, with compression targets, when the material is tightly packed arrows will hit and sag, and it is possible to hit one arrow with another, and damage it. the screen that is about 3 or 4 inches in front of the poly stopping area keeps the arrows straight at all times.

@@archerace7 do you need my info for shipping?

@@carls.6746 If you would, send it to ralph@archerytargets.com I will get you taken care of!!

Steve, if you would call us at 888 233 1976, this target is covered by a warranty, and will be replaced. Thank you!

Thanks for the heads up! Contacted the pro shop where i bought this target from and they replaced it, with no hesitations.

Hello, The CRM is available through our website at archerytargets.com Thank you very much for your interest!